In force since October 1, 2026

Connecticut balcony solar law: limits, dates and what to tell the utility

Connecticut's plug-in solar law has been in force since October 1, 2026. The limit is 1,200 W. Not more than one such device may be used behind a customer's electric meter. The law does not require the customer to notify the utility. This page cannot check your lease, HOA rules, local codes or wiring.

1,200 WLimit as the statute words it. It does not say AC or DC.

limit tier
1
signed, 2026
Jun 4
in force since, 2026
Oct 1
rules last checked
Oct 1

Notice: the law requires none.

Statute: HB 5340 (2026), Public Act 26-127, sections 9 and 10.

The law in Connecticut

Portable solar generation device, one behind each meter (Public Act 26-127 sec. 9): limit 1,200 W.

Dates: signed June 4, 2026, in force since October 1, 2026.

Source: HB 5340 (2026), Public Act 26-127, sections 9 and 10, checked October 1, 2026. Update log

AC or DC. The act says "maximum power output" and does not say AC or DC. This site treats it as the inverter's AC output at the outlet, but the text does not say so. The calculator compares the inverter's AC rating.

Conditions in Connecticut's law

Condition In Connecticut Source
The device plugs into an outlet. It is not hardwired.A standard 120 volt alternating current outlet behind the customer's electric meter.Public Act 26-127 sec. 9 (a)(3)
One device per electric meter.Not more than one such device behind a customer's electric meter.Public Act 26-127 sec. 9 (b)
The device must meet the certification or listing requirement in the law.UL or an equivalent laboratory, meeting UL Standard 1741.Public Act 26-127 sec. 9 (a)(7)
The device must meet the National Electrical Code (and, where the law says so, the state building or electrical code).The State Building Code, the National Electric Code (NFPA 70) and IEEE 1547.Public Act 26-127 sec. 9 (a)(5) and (6)
The device must have a feature that stops it feeding the building or the grid during a power outage.Public Act 26-127 sec. 9 (a)(8)
The device must be intended to offset the customer's own use of electricity at the property.Intended primarily to offset part of the customer's consumption.Public Act 26-127 sec. 9 (a)(4)
What the law says about building, fire and local codes. Being exempt from the utility's interconnection rules is not, by itself, an exemption from them.The State Building Code, the Fire Safety Code, the State Fire Prevention Code and local ordinances.Public Act 26-127 sec. 9 (b)
Power the device makes beyond what the home uses may be charged to the customer as usage unless the customer has a meter that allows net metering. The device must carry a warning saying so.Public Act 26-127 sec. 9 (a)(9)

What Connecticut's law does not settle

  • The act names UL 1741, not UL 3700. Whether a product listed to UL 3700 meets it is not settled.
  • The device is not exempt from the State Building Code, the Fire Safety Code or local ordinances.
  • The law says nothing about landlords, HOAs or condo associations.

Beyond the limit in Connecticut

Other terms in the law

  • The device must not be permanently affixed to a structure. (Public Act 26-127 sec. 9 (a)(1))
  • The electric distribution company may not require its approval before you install or use the device, any fee or charge except charges the device incurs through its use, or controls or equipment beyond what the device has built in. (Public Act 26-127 sec. 9 (c)(1))
  • The electric distribution company is not liable for any damage or injury the device causes. (Public Act 26-127 sec. 9 (c)(2))
  • The State Building Inspector, the State Fire Marshal and the Codes and Standards Committee must consider provisions for installing these devices in the next amendments to the State Building Code and the State Fire Safety Code. The act sets no date for those amendments. (Public Act 26-127 sec. 10)

Power sent back to the grid

The law provides no export payment. The device must carry a warning that output beyond what the home uses is charged to the customer as usage, unless the customer has a meter that allows net metering. Net metering in every state

Permits and codes

Nothing in the section exempts the device from the State Building Code, the Fire Safety Code, the State Fire Prevention Code or any provision of a local ordinance or regulation applicable to such devices. Source: Public Act 26-127, section 9 (b). Permits in every state

Renters, landlords and associations

The plug-in law says nothing about tenants, landlords, homeowner associations or condominium associations. It does say it does not exempt a device from any applicable local ordinance or regulation. Source: Public Act 26-127, section 9 (b). Renters and associations in every state

Check your own kit in Connecticut

Build your kit

Start from

Where

Your kit

2 x 400 W = 800 W of panels, inverter 800 W AC

The AC rating is on the inverter label. It is checked against your state's limit.

In series: leave at 1 unless the kit instructions say otherwise. No state law on this site limits it.

Placement

Panels face

S south, SE southeast, SW southwest, E east, W west

Mounting

Vertical holds up better in winter. Tilted makes more over a full year.

What is specific to Connecticut

Eversource on meters and exported power

In March 2026 Eversource told the legislature's Energy and Technology Committee that most home meters do not recognize power a plug-in device sends to the grid, and may count it as power you used. It called this a standard anti-tampering feature. Ask your utility what meter you have before you choose a kit size.

typical utility metering devices will not recognize the excess generation and may register excess export as customer energy consumption.

Connecticut's association solar rule is about roofs

Since January 1, 2026, Connecticut law makes a provision of a declaration or bylaws that bans or unreasonably restricts solar on the roof of a single-family detached home in a common interest community unenforceable. It does not cover cooperatives or homes that share walls, the owner applies to the association's board, and an association formed on or before January 1, 2026 may opt out by a vote of at least 75% of its board until January 1, 2028. It is about roof systems, not plug-in kits, so ask your association before you buy.

any provision of a declaration or the bylaws of an association that prohibits or unreasonably restricts the installation or use of a solar power generating system on the roof of a unit that is a single-family detached unit, or is otherwise in conflict with the provisions of this section, shall be unenforceable.

One in three Connecticut homes is rented

The Census Bureau counts 33.3% of Connecticut's occupied homes as rented, and 10.9% of homes are in buildings with 20 or more units (American Community Survey, 2024). The plug-in law says nothing about leases, so a renter should check the lease and ask the landlord first.

DEEP on when solar output is used

In written testimony on March 5, 2026, Energy and Environmental Protection Commissioner Katie Dykes said solar without a battery produces at different times from when most residents use power. Because owners are not paid for output beyond their own use, she warned buyers may get less value than they expect, and she asked for a study first. Lawmakers kept the exemption in the final act. Think about how much of a kit's midday output your home would actually use.

The generation profile of solar without battery storage does not match the electricity consumption profile of most residents.

The building and fire office asked about permits

The Department of Administrative Services, which oversees the State Fire Marshal and the State Building Inspector, told the Energy and Technology Committee in March 2026 that the bill should require fire safety code compliance and should say a building permit is needed when a device is connected. The final act names the Fire Safety Code, but sections 9 and 10 never mention a permit. Call your town's building official before you connect a kit.

Without such clarification, the language could be interpreted to suggest that no permit or inspection is required.

Connecticut's next building code is running late

Section 10 of the act asks code officials to weigh plug-in provisions when they next amend the building and fire codes. The Department of Administrative Services says those next codes were due on July 1, 2026 but are delayed while they await approval by the legislature's Regulation Review Committee. Until then the 2022 State Building Code stands, with the 2020 National Electrical Code; the next code is expected to adopt the 2023 edition. Which edition applies to a kit is a question for your local building department.

The next state building, fire safety, and fire prevention codes were expected to take effect on July 1, 2026, but at this time, we await approval of the next codes by the Legislative Regulation Review Committee of the Connecticut General Assembly, and therefore the effective date has been delayed.

Electricity in Connecticut costs more than in almost any other state

Only Hawaii and California have a higher average electricity price than Connecticut, the Energy Information Administration reports. In 2024 natural gas fueled 56% of the electricity made in the state and the two Millstone reactors in Waterford 38%, and about three-fourths of Connecticut's solar power came from small customer-sited systems such as rooftop panels. The rank is the agency's average, not your tariff, so the sizer on this page values a kit's output at the rate you type in from your own bill.

Connecticut has the third-highest average electricity price among the states, after Hawaii and California.

Oil heats about a third of Connecticut homes

Fuel oil or kerosene is the main heating fuel in 35.0% of Connecticut's occupied homes, ten times the national 3.5%, and utility gas in 36.2%. Electricity heats only 20.2%, where across the country it heats 41.8% (Census Bureau, 2024 estimates). A plug-in kit makes electricity and nothing else, so in a home heated with oil or gas it can offset only the lights, appliances and other plugged-in use. Compare the output figures further down this page with the electricity part of your bills, not the heating bill.

Sources for the local facts

Expected output in Connecticut

Every Connecticut city this site covers is in the table, for an example kit of two 400 W panels on an 800 W inverter facing south. Each Connecticut figure is a long-term average of 2005 to 2015 satellite data, not a forecast. Your own panels, direction and shading change the result, so enter them in the Connecticut calculator above. The average residential electricity price in Connecticut (year-to-date through August 2026) is 27.47 cents per kWh. The rate on your bill may differ.

Vertical on a railingTilted stand
Yearly output by Connecticut city, railing against tilted stand
City Vertical (kWh) Tilted (kWh) Comparison bars
Bridgeport7371,097
Hartford7271,058

Open the full calculator for Bridgeport · All states · Outlet and circuit checklist · Compare two kits

What the data say about Connecticut

16th of 21On a south-facing railing Bridgeport makes 737 kWh a year, 16th of the 21 cities this site covers in the US.
Marchis the strongest month on a Bridgeport railing at 74.01 kWh, and June the weakest at 41.27 kWh. June makes about 70% of what December makes: a vertical panel in Bridgeport catches the low winter sun better than the high summer sun.
37%of the yearly railing output in Bridgeport arrives between November and February.
1%more a year in Bridgeport than in Hartford: the strongest and weakest Connecticut cities this site covers.

Same example kit as the table above, on a railing. How Connecticut compares by direction and mounting

Last updated .